Installing ram acer one

You can ground yourself by touching a metal part on your computer case while it is unplugged from the wall. Simply being turned off does not remove any standby voltages, so make sure it's unplugged. Locate your RAM slots. Most motherboards have 2 or 4 RAM slots. RAM slots are typically located near the CPU, though their location may vary depending on the manufacturer or model.

Look for narrow slots about 4. At least one of the slots already has a stick of RAM in it. Remove old RAM if upgrading. If you are replacing old RAM, remove it by pressing the clamps downward on either side of the slot.

If you're having to pull too hard, the clamps are likely not down far enough. You may need to use one hand to push the clamps down while using the other hand to remove the RAM. Take your new RAM out of its protective packaging. Carefully remove the RAM from the shielded packaging. Grip it from the sides to avoid touching the contacts on the bottom or the circuitry on the board.

Line up the notch in the stick of RAM to the break in the slot. Set the stick into the slot and then apply equal pressure onto the stick until the clamps on the side click and lock the RAM in. It'll only fit in one way, so if it's not lining up properly, just flip it around.

You may have to apply a fair amount of pressure, but never force it in. Make sure matching pairs are inserted into their matching sockets. Some are labeled on the board or by color, though you may need to refer to your motherboard layout diagram. Repeat the process for each stick of RAM you want to install. While you have the PC open, remove dust using a bottle of compressed air. This can be a quick fix for general overheating and performance issues. Compressed air cans are available at any office supply store.

Put the case back on the PC. Avoid running your computer while the panel is off, as this will actually reduce the cooling power of your fans. Plug your peripherals and monitor back in. Power on the computer.

Your computer should start normally. If your computer displays the self-test during the startup, then you can verify that the RAM has been installed correctly.

If not, you can verify that the RAM was installed once Windows starts. Power down your PC and re-open it. Then, remove and reseat the RAM. Make sure it clicks firmly into place and then try again.

Check the RAM in Windows. Your RAM will be listed in the System section or at the bottom of the window. Operating systems calculate memory differently and some computers dedicate a certain amount of RAM to specific functions e. All rights reserved. This image may not be used by other entities without the express written consent of wikiHow, Inc. Run a RAM test if there are problems. It may take a while to run, but will discover any errors and display how much is installed.

To run the tool, press the Windows key on the keyboard and type memory into the search bar. Click Windows Memory Diagnostic to launch the tool, and then click Restart now and check for problems to run diagnostics. Method 2. Purchase RAM for your iMac. The type of RAM you need for your iMac depends on the model. Shut down your iMac. Before you get started, fully power down your iMac and disconnect its power cord from the wall. If any other peripherals are connected to your iMac, disconnect those as well.

Because the inner components can run quite hot, Apple recommends waiting at least ten minutes before installing RAM in your iMac. Lay the iMac flat on a clean soft towel.

To protect the monitor, lay a clean cloth down on a flat surface before laying your iMac down monitor-side-down. Open your iMac's memory access door. The steps are different depending on the model: 27" and 21" models or later : Press the small gray button just above the power port to open the memory compartment door.

Lift the door off of the back of the monitor and set it aside. Then, push the two levers outward to the sides to release the memory cage, and pull the levers toward you to see the RAM slots. Set it aside once removed. Placing RAM in the incorrect slots could result in some performance degradation.

Make sure the notch in the bottom edge of your RAM modules match up with the rises in the memory channel on your motherboard. Finally, close up your computer case, plug everything back in, and turn on your computer. Let it run for a few minutes, then restart it and everything will be back to normal. Mentioned in this article. But you must be conscious about if you do not have the necessary sensitivity to do this work.

IFF your pad is not working, then try to do the same operation once more and be aware of how the mini laptop is to be handled at the various parts. I would guess that we are missing a wire in your laptop or something like that. Stone Forest - Come on, I followed this guide to upgrade my son's and my wife's friend's netbooks without problems at all. Fix Your Stuff Community Store. Difficulty Moderate. Steps Time Required 25 minutes.

Sections 7. Flags 0. Step 1 Battery. Add a comment. Add Comment Cancel. Step 2. Step 3. Step 4 Wireless Card. You want to make sure you're putting the RAM into the correct slots, after all, so you can get the full performance out of them. In addition, which slots you go with will also depend on how many RAM sticks you have. If you just have one stick, you don't have to fill Slot 2. In the case of a motherboard with four RAM slots, it's probable you'll want to install your first RAM stick into the slot labeled 1.

A second stick should go into Slot 2, which isn't next to Slot 1. If you have a third stick, it would go into Slot 3, which will actually be between Slot 1 and Slot 2.