Cable television access installation

This will be the cable that runs into the house. Make sure that it is long enough to reach the destination with one cable.

Part 2. Drill a hole into the home. Choose an entry point that will allow you to run the cable with the least amount of stress. Entering into the garage, basement, or attic will allow you to run the cables easier without having to go through as many walls. Ideally, you'd want to run your cable through the attic, garage, or basement until you reach a point where you can go straight up or down through the wall to reach your desired outlet location. Install a splitter to send the signal to multiple destinations.

If you need cable jacks in multiple rooms, you can use a splitter to attach multiple cables inside the home. Every time you split the cable, the signal gets weaker, so avoid splitting too many times. The splitter should be installed inside, preferably at the point where the cable enters the structure.

If you are splitting to more than two locations, you will likely need to install an in-line amplifier. This will boost the signal, allowing you to split to more locations without losing signal quality For cable TV, buy a splitter rated at MHz.

Use fish tape to run cables through walls. Fish tape allows you to easily pull wire through walls without having to tear the whole thing open. You can find fish tape at most hardware and electric supply stores. Do not allow the cable to become bent or crimped, as this will cause signal degradation. Don't try to force the wire through the wall by pulling. Pulling can damage the cable, and most RG6 cable is only rated to 35 pounds of pressure. Fasten cables using cable staples. When stapling cable, do not staple at even intervals.

When a cable is stapled, the foam jacket inside is slightly squished. This can cause some of the signal to reflect. If the staples are evenly spaced, this can lead to a double-image. Use as few staples as possible when running your cable, and try to use cable-specific staples if possible. Do not run cable underneath carpet that will be walked on. Stepping on the cable will lead to the squishing of the foam jacket, hurting signal strength.

Only run cables where no one will step on them. Avoid running the coaxial cable too close to electrical wires. If the coax is too close to electrical wiring, you can get a lot of interference. Keep coaxial cables at least 6 inches away from any electrical wires. If you have to cross an electrical wiring, do so at a 90 degree angle. Avoid running cables near heating ducts as well. Too much heat can warp and damage the cables.

When bending the cable, keep it gradual. Avoid bending the cable at right angles when going around corners. Use a low-voltage box to mount a wall jack. Avoid using a standard electrical box, as this will force you to bend the cable at a 90 degree angle. A low-voltage box doesn't have a large metal box protruding from the back, allowing you to gently curve the cable to the jack.

Hand-tightening will lead to loose connections, which can cause problems down the road. Connect the cable box or modem to the newly installed jack. Follow the instructions for the piece of equipment to perform the initial configuration.

See the guides below for detailed instructions on setting up common cable equipment. Install a modem Install a cable box You can use an RF signal meter to ensure that enough signal is being transmitted through the cable. Cable TV and cable internet work on the same cable, you just need to use a splitter to connect one cable to the set-top box and one on a cable modem.

Yes No. Not Helpful 2 Helpful Either way can be done, but usually over the doorway avoids more problems with cable placement. Cable Access Wall Plates 14 Products available. Compare Products View 15 30 45 60 Favorite this. Added to Favorites Go to favorites. Remove from favorites? Yes No. Compare Compare Now. View Details. A full-motion TV mount swivels and tilts for the maximum number of possible viewing options. You can also mount your TV from above with a ceiling TV mount.

If you need help choosing and installing a TV mount, contact a TV wall mount installer near you. You can hide wires from a hanging TV on a wall by putting them behind the wall.

However, this requires some drilling or buying an in-wall power kit. To get the job done right, and avoid risking damage to your wall, hire a professional TV wall mount installer near you. Yes, you can mount a TV without studs using hollow wall anchors, which are used to hang objects on a wall, according to Digital Trends.

However, these have limits. Make sure they can handle the weight of your TV. Yes, a TV mounting service is often able to install a home theater system as well. Companies and technicians who offer flat-screen TV wall mount installation service may offer package deals on installing surround sound and other parts of a home theater installation.

To find the best TV mounting service near you that can install a surround sound system in your home, compare companies side by side. TV wall mounts are generally universal. Thanks to this set of standards, any mount you buy is likely to be a universal TV wall mount. However, exceptions do apply. Many TVs can be mounted with standard equipment. However, you need to cover a few details before mounting a TV. Know the size and weight of your TV before you purchase a mount.

Match this number to the VESA-compatible mount to ensure compatibility. You never pay to use Thumbtack: Get cost estimates, contact pros, and even book the job—all for no cost.

Join as a pro. See all. Events and more. Other Info. Find a cable tv wiring installation near you 20 near you. Zip code. Yes No. Client has mount or stand? TV installation location Wall mount above fireplace Wall mount Recessed wall mount Not sure, need professional's help to decide Other.

Handy Bear Fully Vaccinated. Top Pro. Exceptional 5. In high demand. Jonathan M. View profile. Great 4.