Installing a weld wire fence

The top of the fence is marked by a cap rail. Fit the rails into their notches and indicate the locations where screws will be installed. Before attaching the pieces with lag screws, drill pilot holes. This stage benefits from a second pair of hands.

Roll out the welded wire or mesh fence against your posts to secure your fencing to your posts. Keep the fence taut against the posts and level with the rails if applicable. Attach your welded wire fence to the posts or rails with high-quality fasteners for a welded wire fence. Using a mixture of soil and gravel, cover the fencing in the trench. The mixture aids drainage, which is especially important if you plan to keep animals confined within your fence.

A gate should be installed if your fence is used to keep animals in. When laying out your design, consider how big your gate will be. A wheelbarrow can fit through most gates, which are around 36 inches wide.

You can either buy or make your own gate. Attach the door to the fence by using latches and hinges. The use of gates is not required. Individual flowerbeds can be fenced in instead. If you plan carefully, bury the poles and fencing, use high-quality fasteners for welded wire fences, and add rails, your fence will last a long time.

Make sure the wire fencing is taut and covers the posts. Set yourself up for success by familiarizing yourself with these welded wire fence building suggestions. Step 4 You will need one post for each corner.

Generally you want your posts to be between 7 and 10 feet apart. Divide the length of each side by feet to figure how many posts you will need per side. Add up the posts from each side and the corners. Step 5 Place your corner T-posts. Remove your wood marking stake. In its place, pound your T-post 2 feet into the ground with a hammer or a steel post driver. Pound the posts in straight. Step 6 Once all the corner posts are pounded in, tie a string to each post, close to the top. Attach a line level to the string to make sure your posts are even.

The string will also help you keep each post in a straight line. Step 7 Measure the distance from the corner to the first post you want to place.

Pound the post into the ground. Repeat with the remaining posts, trying to keep the posts at a degree angle to the ground. Remove the string. Step 8 Starting at a corner, attach the end of your roll of welded wire. Use the baling wire or metal ties to tie the wire to the post at the top, the middle and the bottom. Once the roll is attached, carefully unroll and stretch the wire to the next post.

Tie the wire to the pole. Continue to the corner. Once you reach the corner, carefully stretch the wire around the corner and continue to the next post. Welded wire comes in rolls from 25 to feet. Smaller rolls are usually easier to handle, but larger rolls are cheaper. Once you have all of the measurements done, divide the length of each side by feet depending on how many feet you want between fence posts to find out how many fence posts you will need.

When setting up a fence post, it is important to have the correct measurements for your post. Remember, a fence post is buried two feet deep into the ground, so you should add two feet to the desired height of the fence post. You can dig deeper if you like, but your fence post will have to be longer to make up the difference , depending on how high you want the fence to be.

When digging a hole for your fence post, you can use a shovel or a post hole digger. Follow the allotted measurements you came up with to make sure your fence is the height you want it.

Once you have the hole for the fence post, you will want to lay down some gravel in the hole. About six inches will do. Gravel acts as a barrier to keep moisture from getting to the fence post.

If moisture gets to your fence post and you are using a wooden post, the wood will rot quickly. Rotting wood will easily ruin your fence if you are not careful. Placing gravel is also a good idea if you decide to use a metal fence post because it will help keep the post sturdy.

Then, place the fence post in the ground. Make sure the post is level and at a degree angle to the ground. Having someone help you here is crucial because one mistake will make your fence crooked.

Once the post is level, slowly add concrete to fill the hole. Concrete helps keep moisture away from the fence post while also holding the post in place. Concrete is almost always used when setting fence posts. You will repeat this step with every fence post you need for your welded wire fence. After setting the fence posts, you will want to wait a few days to make sure the posts are completely set.

Check frequently the first 24 hours to make sure the post does not move. Once all of your fence posts are set, you are ready to attach the welded wire to create your fence. If you are using a wood post for your fence, you will use a stapler to attach the wire to the posts. If you choose to use a metal post , you will use baling wire or metal ties to tie the wire to the top, middle, and bottom of your metal fence post. Once you have your materials, you will start at a corner post and roll out the welded wire.

It is helpful to have another person to help you hold the fencing so either you or them can secure the welded wire to the fence post. Stretch the fencing as far as you can to make sure the fence is tight and secure. If you run out of material, attach the end of the first roll at the last post it reaches and start a new one on the same post. You can go back and use wire clippers to remove the excess wire. It is important to make sure the fencing stays level as you attach the welded wire to the fence posts.

It is helpful to stop every other fence post to make sure the fencing is level. After you have placed the welded wire for your fencing, you should have a spot left for your gate.